Home Products Standard Range Materials Industries Capabilities Quality About FAQ Guides Send RFQ
Home › Guides › How to Specify a Rubber Part
Guide

How to specify a rubber part for a quote

A clear RFQ gets a quote that matches your part. These are the details we look for on a drawing or enquiry for a moulded or extruded rubber part, and what the common specification codes mean.

Checklist

What to send with an RFQ

  1. The part. A drawing (PDF, DWG, DXF or STEP), or a sample if there is no drawing.
  2. Material. The polymer (EPDM, silicone, NBR, FKM, neoprene or SBR), or the duty if you are not sure.
  3. Hardness. Shore A with a tolerance, for example 70 ±5 Shore A.
  4. Conditions. Temperature range, what the part touches (oil, fuel, water, steam, chemicals, weather) and the pressure or compression.
  5. Specification. An ASTM D2000 call-out or your own material specification, if you have one.
  6. Tolerances. The ISO 3302-1 class, if your drawing uses one.
  7. Quantity. Quantity per year, in pieces or metres.
  8. Extras. Colour, marking, adhesive backing and packing needs.
  9. Confidentiality. Need an NDA first? Ask us and we will sign one before reviewing your drawing.
ASTM D2000

Reading an ASTM D2000 call-out

ASTM D2000 classifies rubber materials with a line call-out on the drawing. A call-out such as M2BC714 reads left to right: M means the values are metric; 2 is the grade, the level of test requirements; the first letter is the type, set by heat resistance; the second letter is the class, set by swelling in a test oil; the next digit is hardness (7 = 70 ±5 Shore A); the last two digits are minimum tensile strength in MPa (14 = 14 MPa).

Letters and numbers after that are extra tests: for example A for heat resistance, B for compression set, C for ozone, F for low temperature and Z for a special requirement written on the drawing. We compound to the ASTM D2000 call-out on your drawing.

ISO 3302-1

Tolerance classes for rubber parts

ISO 3302-1 sets dimensional tolerance classes for solid rubber parts: M1 to M4 for moulded parts, with M1 the tightest, and E1 to E3 for extruded sections, with E1 the tightest. Rubber cannot hold metal-part tolerances, so pick the loosest class the fit allows. Tell us the class on your drawing and we confirm what we can hold before tooling.

Compression set

Why compression set matters for a seal

Compression set measures how much of the applied compression a rubber sample fails to recover after it is held compressed at a set temperature for a set time. For a seal, lower is better: a low figure means the seal keeps pushing back against the joint. ASTM D395 Method B, compression under constant deflection, is the usual test.

Samples

From sample to production

Fast prototyping and first-off approval come first. Once you approve the sample, production runs on the same tooling. Test reports and compound test certificates are available on request, as are tensile strength and elongation figures for the compound.

FAQ

Common questions

What if I have no drawing?
Send a sample. We measure it, allow for wear and draw it up before tooling.
Which file formats can I send?
PDF, DWG, DXF, STEP, JPG or PNG. The RFQ form takes one file up to 8 MB.
Do you sign an NDA before seeing a drawing?
Yes, on request. Ask us and we will sign one before reviewing your drawing.
Request for quote

Send your RFQ

Tell us what you need. Fields marked * are required. Everything else helps us recommend the compound.

About Exonel Industries

Exonel Industries makes custom moulded and extruded rubber components in Howrah, Kolkata, West Bengal, and supplies manufacturers across India. We work in six base polymers, Silicone, EPDM, FKM, NBR, Neoprene and SBR, formulated into hundreds of compounds. Compounding, tooling and production are done in-house. Send a drawing, a sample or a specification for a quote.

💬 ✉
WhatsApp Call Email Send RFQ